GASKETS - Applications - Intake
Email Page To a Friend
 
INTAKE GASKETS
Matched to Edelbrock Performer and Performer RPM cylinder heads and manifolds, our Intake Gaskets allow for optimum flow and performance. The new MP-2N MicroporeŽ technology does not use solvents making our gaskets environmentally friendly. Impervious to most chemicals, this synthetic fiber composite provides a high recovery under load. This means that when compressed, the gasket will conform to any imperfections on the sealing surface even using lower flange pressures. A nitrile bead around each port opening makes the seal even better.

AMC
Application Specs Part #
1967-69 290-390;
1970-91 290-304-343; 360-390-401
port 1.13" x 2.21"
.060" thickness
#7213

BUICK
Application Specs Part #
1967-76 400-455 port 1.15" x 2.38"
.060" thickness
#7246

CHEVROLET
Application Specs Part #
1958-1986
302-327-350 S/B
port 1.28" x 2.09"
.060" thickness
#7201

#72018
Set of (10 pr.)
1958-1986
400 S/B
port 1.28" x 2.09"
.060" thickness
#7201
1958-1986
E-Tec 302-327-350 S/B
port 1.28" x 2.09"
.060" thickness
#7235 (C)


#72358
Set of (10 pr.)
1958-1986
E-Tec 200, 302-327-350 S/B
port 1.26" x 2.24"
.060" thickness
#7215 (C)
1958-1986
E-Tec 400 S/B
port 1.08" x 2.11"
.120" thickness
#7235 (C)
1965-90 Rectangular Port
Mark IV, 396-402-427-454 B/B
port 1.82" x 2.54"
.060" thickness
#7202
1965-90 Rectangular Port 6 bolt flange w/ no crossover
Mark IV, 396-402-427-454-555 B/B
port 1.82" x 2.46"
.060" thickness
#7208
1965-90 Oval Port
Mark IV, 396-402-427-454 B/B
port 1.82" x 2.05" .060" thickness #7203
1991 & later Rectangular Port
Gen V & VI, 454-502 B/B
port 1.82" x 2.54"
.060" thickness
#7202
Intake Manifold. SBC Intake Manifold 2814.
For GM Cast Iron Bowtie Vortec
Cylinder Head. .060" Thick.
#7206
Intake Manifold. SBC Intake Manifold 2814.
For GM Cast Iron Bowtie Vortec (10 PACK)
Cylinder Head. .060" Thick.
#72068
Intake Manifold. SBC Intake Manifold 2814.
For GM Cast Iron Bowtie Vortec
Cylinder Head. .120" Thick.
#7207
Intake Manifold. SBC Intake Manifold 2814.
For GM Cast Iron Bowtie Vortec (10 PACK)
Cylinder Head. .120" Thick.
#72078
Intake Manifold. SBC
For Chevy 90-degree V-6
port 1.28" x 2.10"
.060" thickness
#7209
Intake Manifold. SBC 23-Degree Intake Gasket
For Edelbrock Victor Jr and Victor High-Port Intakes
port 1.31" x 2.02"
.060" thickness
#7217
Intake Manifold. SBC 18-Degree Intake Gasket
For Edelbrock 18-degree High Port Cylinder Heads
port 1.23" x 2.13"
.060" thickness
#7218

CHRYSLER
Application Specs Part #
1966-87
318-340-360
port 1.17" x 2.30"
.060" thickness
#7276
1992 & Later
Magnum
port 1.18" x 2.18"
.060" thickness
#7277
1958-1979, 361-383-400,
413-426 [except Hemi],
and 440 engines
port 1.23" x 2.27"
.030" thickness
#7225 (B)

FORD
Application Specs Part #
Small Block Ford Intake Gasket
For Edelbrock Victor Jr Cylinder Heads w/o Heat Crossover
port 1.28" x 2.10"
.060" thickness
#7219
1963-96, 289, 302 S/B [except Boss] & 351W
1982-96, 5.0L & 5.8L
port 1.20" x 2.00"
.060" thickness
#7220


#72208
Set of (10 pr.)
1970-74 351 Cleveland,
1975-85 351M,
1971-81 400M
port 1.52" x 2.16"
.060" thickness
#7265
1958-76
390-428 FE
port 1.20" x 2.10"
.060" thickness
#7224
1968-1987
429-460 B/B
port 1.98" x 2.26"
.060" thickness
#7223 (D)

HONDA
Application Part #
1992-00 D16 - intake manifold gasket (D16Y7 motor will require trimming of gasket) #15005
1994-00 B16/B18C5 - intake manifold gasket #15042
1994-00 B18C1 - intake manifold gasket #15042
1994-00 B18B - intake manifold gasket #15043

OLDSMOBILE
Application Specs Part #
1965-76
400-425-455
port 1.44" x 2.44"
.060" thickness
#7284

PONTIAC
Application Specs Part #
1961-1980 326-389-421-428-455 port 1.18" x 2.20"
.060" thickness
#7280

EDELBROCK GASGACINCH
Gasgacinch assures proper sealing of all gaskets used in a manifold installation. Also effective on water pump, oil pan and valve cover gaskets. Water and oil resistant. Allows easy gasket removal during parts disassembly.
Application Part #
Edelbrock Gasgacinch #9300
(A) Does not include end seals; Edelbrock recommends he use of silicone sealant in place of end seals
(B) Must be used with OE-style valley pan
(C) Does not have embossed silicone bead
(D) Does not fit CJ or SCJ
(E) For use with Bowtie Vortec #2814 intake
Sign up for our Newsletter  
Privacy Policy | Order A Catalog | Warranty Information| Site Map
©2008 Edelbrock Corporation