GASKETS - Applications - Exhaust
 
EXHAUST GASKETS
Edelbrock Exhaust Gaskets are made of EnCore™ HTX-900; a high-density non-asbestos fiber/metal core composite material consisting of two graphite coated, heat resistant fiber blended sheets that are mechanically and chemically fused to an expanded steel core. The finished product provides high heat resistance, excellent load retention and unmatched sealing performance on exhaust manifold and header applications. A 50% recovery rate allows for gasket expansion in the event your header loses the proper header bolt torque.

AMC
Application Specs Part #
1967-69 290-390;
1970-91 290-304-343; 360-390-401
1.80" x 1.30" #7239

BUICK
Application Specs Part #
1967-76 400-455 1.20" x 1.63" #7247

CHEVROLET
Application Specs Part #
1958-1986 302-327-350 S/B 1.50" x 1.50" #7204
1958-1986 400 S/B 1.50" x 1.50" #7204
1958-1986 E-Tec 302-327-350 S/B 1.50" x 1.50" #7204
1958-1986 E-Tec 400 S/B 1.50" x 1.50" #7205
1992-1997 LT1/LT4 1.385" x 1.400"
(D Shaped)
#7248
1958-1965 348/409 "W-Series" (F) 1.813" x 1.75" #7241
1965-90 Rectangular Port Mark IV, 396-402-427-454 B/B 1.940" (round) #7205
1965-90 Oval Port Mark IV, 396-402-427-454 B/B 1.940" (round) #7205
1991 & later Rectangular Port Gen V & VI, 454-502 B/B 1.940" (round) #7205

CHRYSLER
Application Specs Part #
1966-87 318-340-360 1.75" x 1.25" #7236
1992 & Later Magnum 1.50" x 1.20" #7237
1958-1979, 361-383-400, 413-426 [except Hemi] and 440 engines 1.84" x 1.33" #7226

FORD
Application Specs Part #
1963-96, 289, 302 S/B [except Boss];
1982-96, 5.0L, 5.8L& 351W
1.25" x 1.48" #7227
302 E-Boss and 351W E-Boss [Clevor] Conversion 1.98" x 1.56" #7262
1970-74 351 Cleveland 1.98" x 1.56" #7262
1958-76 390-428 FE 1.40" x 2.04" #7229
1968-1987 429-460 B/B 1.50" x 2.10" #7228

OLDSMOBILE
Application Specs Part #
1965-76 400-425-455 1.95" x 1.56" #7238

PONTIAC
Application Specs Part #
1961-1980 326-389-421-428-455 1.880" #7281
 
(A) Does not include end seals; Edelbrock recommends the use of silicone sealant in place of end seals
(B) Must be used with OE-style valley pan
(C) Does not have embossed silicone bead
(D) Does not fit CJ or SCJ
(E) For use with Bowtie Vortec #2814 intake
(F) For use with large port applications, including Edelbrock RPM heads #60809/#60819, will not fit factory heads
(G) For use with large port applications only
(H) For use with Edelbrock RPM heads #61699 only
(I) For use with small port applications only
(J) Graphite style
(K) Gasket is trim-to-fit for port matching
Sign Up To Receive Our Newsletter & Members Only Specials  
Privacy Policy | Order A Catalog | Warranty Information| Site Map
©2009 Edelbrock Corporation